• Diefenthal Folding Hunter

    I thought that some of you might like a look around a bit of cutlery produced by one of Solingen’s finest. This is a folding hunting knife made by Diefenthal. It’s not to everyone’s taste, I know. It’s got stag scales. It’s heavy (very heavy). It’s got stainless blades, which are hollow ground AND recurved. It is a lockback, with a rather ungainly looking stud. These are not the virtues designed to appeal to the modern urban knife buyer. Nevertheless, I have wanted one for a long time. I had a stockman by the same people, which I lost quite recently – well, I haven’t seen it for a bit (which is worse). And this big old thing rolled up in the troubled post a couple of weeks back.




    I cannot pretend otherwise. I like this knife a lot. There’s a lot to like. In fact, all the qualities indicated as sins above, are the very excuses for loving this thing. It is weighty, textured and positive in the hand. The action is excellent, and the hollow ground recurved main blade is an absolute revelation for me. In short it has a lot of presence.

    The stag scales are well chosen. The fit and finish, the detailing of pins and bolsters is admirable. Blades all align perfectly. The steel is listed as D2000, a variation on the 440C recipe, I think, and looks and feels great. Everything that needs to be sharp is razor sharp – especially the saw, which is a bit of a hooligan, and has a complex concave grind. This is one of the most interesting aspects of the knife. It cuts through wood and bone with extreme efficiency, and reminded me of the first time I ever used a jet saw.

    It’s seen here, for scale, in the company of Fallkniven U2 and a Northwoods Congress – which is 4” long overall. And there’s a pic with another hunty type – a big Boker lockback.




    So, it had a bit of a workout over the past weeks or so. It is very robust. Diefenthal’s knives have been compared with old Pumas. In a sense, this is an accurate comparison. Both are strong, made with similar kinds of materials, even have similar sounding etchings on the blades. I would say that there is something slightly more polished about the Diefenthal though. The tolerances are a fraction higher. The Pumas state cutting problems very effectively, whereas the Diefenthals seem to go one step further in articulating those problems, and refining them. Also Puma don’t do corkscrews, so much!

    The main thing to note about this knife in use is the complex geometry of the main blade. There is some portion of the cutting edge that could be used for almost any task. Broad and swedged at the distal end, it is superb for paring, slicing and so forth. The narrower section of the blade near the handle is good for whittly work. Though I should say, whilst plenty stout and easily able to take the strain, you might wish to consider another blade for trimming and shaping wood, especially dry wood. The recurve allows for cuts that seem to roll on effortlessly and endlessly.

    The saw features a flattened end which might be useable for a srewdriver – though the length of the saw itself, and the torques involved, might put the pivot pin (though not the saw itself) in jeopardy. It also incorporates a bottle opener/cartridge extractor – much more sucessfully resolved as a design element. The concave grind on the saw indicates its usefulness for cutting through wet stuff like greenwood, bone and the like. This, and features similar, appear often on hunting saws, and is perhaps part of a bespoke tradition. It is a lovely bit of engineering, and quite uncompromising.





    As you can see, it is a knife that would prefer a pouch or a hip sheath of some kind. It is bulky for the jeans pocket – though I am quite happy with carting it about like that – but fits the hand very well for the very reason of that bulk. You can really get a hold of it. The knife was not supplied with a sheath, but having got hold of Diefenthal’s address via Ludi, I am going to get in touch with them directly to see if they have one (I got this one from toolshop.de).

    The gralloching blade is another piece of beautiful modelling. It has a fine and quite acute hollow grind, and arrived extremely sharp. As a kind of draw-knife it works very well, but again perhaps it would just do – you might want something purpose made for that kind of use. It serves.



    I have a soft spot for the German woodland romance that this kind of knife conjures up. It’s all leather shorts, mistiness, feathered caps, forested inclines and vistas – little flasks of herb infused, fortified wine, sausages and dense brown bread (maybe not quite so appealing, when put like that, perhaps ). Hubertus and other German makers produce very similar items, and I look forward to the opportunity of one day having a go with a Hubertus built along these lines. My suspicion is that they are not produced to the same standards, but the designs of the Hubertus are very appealing, nevertheless.



    I can’t recommend this for urban edc – well not fully, but that is only because of the carry laws. It is a SAK on the grand scale. I am very impressed not only by the way this is manufactured (the usual ‘built like a BMW’ line that is often rolled out in these circumstances is totally appropriate, here). But I am even more taken by the design of the main blade. The single blade version of this knife looks terrific if you are into the whole bolstered stag/rosewood aesthetic, and is very affordable (approximately Ł60). I am greatly tempted by it. More slender, more direct. I’d really like to be able to get a hold of one of the blades and send it to someone like Karel Koci, and ask him to work some magic on it. Unfortunately (as Ludi discovered) Diefenthal will not release their blades alone.

    The blade is stiff and sharp – not prybar-ish – and directed towards precise outdoor culinary use, and kind of suits me. The steel is hardened to about 57/58. I have yet to tell about its toughness – because it hasn’t dinged, rolled or chipped, and I have had no reason to sharpen it. So, we’ll just see about that. I’ll update when and as. It has picked up a few surface marks, though only as you’d expect.



    All in all? Bloody marvellous. A different tip from a Spydie or a Sebbie in the working knives niche, and speaking of older, more European values, I think. Certainly if you are looking for a light and pragmatic knife, don’t buy this. But if you are looking for texture, presence a sense of tradition and personality, maybe give it whirl. Hope you like the pics. I meant to add an ‘in hand’ picture, and will do when I can.

    This article was originally published in forum thread: Diefenthal Folding Hunter started by Noddy View original post
  • Subscribe

    Become a subscibing member by clicking the button below.

    Subscribe
  • Sponsored Links..

  • Sponsored Links...

  • Recent Forum Activity

    avoidspam

    What EDC are you carrying today?

    Thread Starter: avoidspam

    Thought I'd give this a go. Sorry if it's been tried before but I quite like the version on the other side of the pond. Everyone gets a bit creative with their camera's... Plus it's a nice opportunity to see what's out there....:) Sam

    Last Post By: ted2 Yesterday, 08:46 PM Go to last post
    Albert E

    Birds,bugs etc,around us!!

    Thread Starter: Albert E

    Hi!!We all see and sometimes take pictures of animals around our house,or during our travel vacations!!Here some!!Maybe you have a few from your area too!! A mantis in my garden.

    Last Post By: Albert E Today, 02:32 PM Go to last post
    Celtic Dragon

    Lets see your rifles?

    Thread Starter: Celtic Dragon

    As mine is still in the smiths (and has been for 6 weeks and no end in sight) The parts I have here are being fantasy pimped :D For those results you'll have to wait a few days. In the mean time to aliviate my suffering, lets see yours :D be it pcp, springer, rimmie or centrefire.

    Last Post By: John56 Today, 01:40 AM Go to last post
    Simon G

    Let's See Your Pistols

    Thread Starter: Simon G

    So, in the "let's see your rifles" thread, Rapidboy suggested a pistol thread. And as we always listen to the mods on here, let's give RB what he wants! (As opposed to what he needs!:D ) For UK mainland residents, obviously muzzle loaders and air. But for our friends in the not so discriminated...

    Last Post By: johnbaz Today, 12:42 AM Go to last post
    gruffalogriff

    Opinel Mod

    Thread Starter: gruffalogriff

    Modified this Openial No8 for my daughter. She found an antler last year while we were walking a Munroe in the Scottish highlands so i used a bit of that for the handle. Turned down the collar end on the lathe to fit the Openial hardware slotted the handle by clamping it in the woodworking vice and...

    Last Post By: gruffalogriff Today, 10:20 AM Go to last post
    Abyrvalg

    Laminated...

    Thread Starter: Abyrvalg

    This knife I made with a wonderful laminated blade made by my friend Alessio Salsi. I really like the look of this steel and i think it looks better than any Damascus... So, blade core is high-carbon "white steel" and sides are non-hardenable soft steel, 11 layers on each side. Handle and...

    Last Post By: Abyrvalg Today, 03:06 PM Go to last post
    polecat

    Bigger Bowie with Hamon.

    Thread Starter: polecat

    Been Forging out a 10 inch Bowie style blade and got around to starting the polishing today, needs alot more work yet but its starting to look the part now. Think I finally understand how to set up the Hamons on this steel, but getting the best from the polishing is hard work. Not easy to...

    Last Post By: polecat Today, 08:14 PM Go to last post
    BGC_Tom

    Overcoming loctite

    Thread Starter: BGC_Tom

    Hi all, So I recently bought a Bradford Guardian 3, along with a pair of ‘3D’ micarta scales to replace the G10 ones. The problem is, when I came to take the old scales off I just could not budge the screws! I’ve already broken one driver bit (one of those two-prong ‘spanner’ bits) and still...

    Last Post By: PuukkoJim Yesterday, 09:43 PM Go to last post
    camperman

    Japanese boning Knife

    Thread Starter: camperman

    Here is my idea of a Hankotsu boning knife. Ironwood scales. 12c27 steel.

    Last Post By: tomancik Today, 07:47 AM Go to last post
    surfer

    A new "Wanderer" with copper and brass

    Thread Starter: surfer

    Hello, I just finished this 10cm Wanderer! 10cm blade from 1.2442 at 61HRC, silver soldered guard from brass, spacers from aluminium, fiber, copper, micarta and leather, pommel from AAA sambar and copper with a 7mm Remington Mag. cartridge.

    Last Post By: Wrangler Today, 04:51 PM Go to last post
  • Alexa

    Review britishblades.com on alexa.com